Danby DMW902W User Manual download pdf (Page 12)

• For Defrost and One Stage Cook, follow

steps above. Before touching START pad,

touch COOK pad, enter time using number

pads and power if desired. Then touch

START pad. MEM shows on the display until

oven switches ( beeps twice) to COOK.

See page 9 for detailed information on

Staged Cooking.

• For Defrost and Two Stage Cook, follow

steps above. Before touching START pad,

enter two COOK programs, using a different

(usually lower) power for the second COOK.

MEM shows on the display during both

Defrost and first COOK stage. Oven beeps

twice when switching stages.

INTERRUPT DEFROSTING (to stir food,

turn it over, or provide other attention).

Either touch START/STOP pad or open the

oven door. Unelapsed time will show on dis-

play; reclose the door and restart to contin-

ue. Or if no additional defrosting is required,

touching RESET pad clears the display

5.SETTING "COOK BY WEIGHT"

This feature is for roasting meats in the

microwave. Its pre-set times and power

levels give better results than microwaving

at one power only, and it is easier to

microwave meat with this setting than with

cookbook instructions because you do not

have to calculate "minutes per pound" cook-

ing times. As soon as you enter the code

(which tells the oven the type of meat) and

the weight, the oven calculates

cooking time.

Meat must be defrosted and at refrigerated

temperature to correspond with the pre-set

times in this code.

Meat-roast weights in about the 3 to 5

pound range microwave best, COOK BY

WEIGHT code allows a setting lower than 3

lb. but no higher than 5 lb. Depending on

code , two beeps signal an error in setting a

too-high weight.

"Cook by Weight" programs the oven to stop

after partial cooking, so meat won't overcook

on one side. Turn meat over, then touch

START pad to continue cooking.

•Touch COOK BY WEIGHT pad. Word

prompt shows ENTER CODE on display.

• Select desired code from 1 through 3. Door

frame (open the door to review ) and chart

at right describe types of food for each code.

• Enter the one-digit code by touching the

correct number pad.

• Check weight of meat . Weight must be in

pounds and ounces. If label gives weight in

pounds only, change the fraction of a pound

to ounces using chart on page 11.

• Enter weight. Word prompt ENTER shows in

display and 0's show where LB and OZ

should be entered. LB flashes until you enter

pound(s) by touching correct number pad.

When pound(s) has been entered, LB will

stop flashing and OZ will flash. As soon as

all these digits have been set, display will

immediately show cook time. Ounce weights

less than 10 must be preceded by a 0. As

soon as three digits are set, display immedi-

ately shows cook time.

•Touch START/STOP to start oven, CODE

flashes in display as time counts down.

Interior light goes on and fan sound is

heard. Oven beeps once after about 1/4

time. If necessary, check thin edges of meat

and poultry for shielding.

• After partial cooking, oven beeps twice and

stops. Interior light goes off but time remains

on the display. Stop is to prevent meat's

overcooking on one side before turning over.

After turning meat over, touch START pad to

resume the time on display and

finish cooking.

• After total cooking time, 4 long beeps sound

and END appears in display. Touch RESET

or open oven door to clear END before start-

ing another cooking function. Let roast stand

few minutes before carving.

When oven switches power levels, you may

observe change in lighting intensity and/or

change in blower sound. This is normal.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 50 51

Comments to this Manuals

No comments

Danby DMW902W User Manual Page 12

Comments to this Manuals

Related products and manuals for Microwaves Danby DMW902W