Danby DAR154BLSST Operations Instructions download pdf (Page 4)

INSTALLATION INSTRUCTIONS

BEFOR USING YOUR

ALL REFRIGERATOR

INSTALLATION OF YOUR

ALL REFRIGERATOR

• Remove the exterior and interior packing.

• Before connecting the refrigerator to the power source,

let it stand upright for approximately 2 hours. This will

reduce the possibility of a malfunction in the cooling

system from handling during transportation.

• Clean the interior surface with lukewarm water using a

soft cloth.

• When disposing your appliance, please choose an

authorized disposal site.

• Place your refrigerator on a floor that is strong enough

to support it when it is fully loaded. To level your

refrigerator, adjust the front leveling leg at the bottom of

the refrigerator.

• Locate the refrigerator away from direct sunlight and

sources of heat (stove, heater, radiator, etc.). Direct

sunlight may affect the exterior of the cabinet and heat

sources may increase electrical consumption. Extreme

cold ambient temperatures may also cause the unit not

to perform properly.

• Avoid locating the unit in moist areas.

• Plug the refrigerator into an exclusive, properly

installed-grounded wall outlet. Do not under any

circumstances cut or remove the third (ground) prong

from the power cord. Any questions concerning power

and/or grounding should be directed toward a certified

electrician or an authorized service center.

ATTENTION

• In order for the cabinet to remain efficient do not over

load it;

• Do not open the door unless necessary;

• Do not cover shelves with aluminum foil or any other

shelf material which may prevent air circulation;

• Should the refrigerator be stored without use for long

periods it is suggested, after a careful cleaning, to leave

the door ajar to allow air to circulate inside the cabinet in

order to avoid possible formations of condensation,

mold or odors.

INSTALLATION SPECIFICATIONS

FOR BUILT IN APPLICATION

• It is recommended that you do not install the unit directly beside

a wall. This is to allow the door to have a greater then 90° opening

swing. A limited door swing may lead todamaging the door gasket.

• The rough cabinet opening must be on a level floor area and at

least 26” deep by 24” wide. The opening should also have a

height

• The electrical outlet may be positioned from within either side of

the adjacent cabinetry, or the rear of the shaded area

(as shown in Fig A).

• If the electrical outlet is located inside the adjacent cabinetry, cut a

1-1/2” diameter hole to admit the power cord. If the cabinet wall is

metal, the hole edge must be covered with a bushing or grommet.

TOOLS YOU WILL NEED

While performing installations described in

this section, gloves, safety glasses and

goggles should be worn.

/2”d iam. hole

* Ifelectricalout-

letisin

cabinetry.

/4” from

underside

countertop

tofloor

Cabinets

square

and

plumb

FigA

24”

underside of

countertop to

floor.

Cabinets

square

and plumb

1 1/2” diam. hole

* If electrical outlet

is in adjacent

cabinetry.

Electrical Access

Fig.A

26”

• This refrigerator is in accordance with Energy Star, but in order to

get the best energy efficiency, the built-in size should be:

Width- 25 9/16” x Height- 35 7/16” x Depth- 26”

• If you did not leave enough installation size for the refrigerator

in your kitchen, please refer to the installation drawing below.

Attention: The below installation method will not affect the

performance of the unit but will affect the accordance with

Energy Star.

NOTE:

of at least 34 3/4”.

34 3/4 ” from

1 2 3 4 5 6 7 8 9 ... 26 27

Comments to this Manuals

No comments

Danby DAR154BLSST Operations Instructions Page 4

Comments to this Manuals

Related products and manuals for Unknown Danby DAR154BLSST