Danby DR2099BLGLP User Manual download pdf (Page 10)

CARE AND CLEANING (cont’d)

CLEANING THE CONTOURED WELL AREAS,

BURNER CAPS, AND BURNER HEADS

The contoured well areas, burner caps and burner

heads should be routinely cleaned. Keeping the burner

ports clean will prevent improper ignition and an

uneven flame.

To clean the recessed and contoured areas of the cook-top:

• If a spill occurs on or in the recessed or contoured

areas, blot up spill with an absorbent cloth. Rinse with

a clean, damp cloth and wipe dry.

To remove and replace the surface burner caps and

surface burner heads, remove in the following order:

1) Surface burner grates

2) Surface burner caps, and

3) Surface burner heads

• Reverse the procedure above to replace the surface

burner caps and surface burner heads.

•Use a soap-filled scouring pad or a mild abrasive

cleanser to clean the surface burner caps and surface

burner heads. The ports or slots around the burner head

must be routinely cleaned. If residue still remains in

these ports, use a small-gauge wire or needle to clean

the slots or holes.

• For proper flow of gas and ignition of the burner do

not allow spills, food, cleaning agents or any other

material to enter the gas orifice holder opening.

Always keep the surface burner cap and surface burner

head in place whenever a surface burner is in use.

THE COOK-TOP IS NOT REMOVABLE. DO NOT

ATTEMPT TO REMOVE OR LIFT THE COOK-TOP.

Oven Surface:

• Be sure to wear rubber gloves to protect your hands.

• Do not use oven cleaners, cleaning powders, steel

wool pads, synthetic fiber pads, or any other

materials that may damage the surface finishing.

• If any acid, grease, sugar, etc. spills on surfaces while

they are hot, use a dry paper towl or soft cloth to wipe it

up right away. When the surface has cooled, clean with

soft cloth and warm soapy water; rinse well.

• You may also use a solution of vinegar and water to

clean the oven surface. Use vinegar to remove hard

stains (white stains).

• Heavy spattering or spillover may require cleaning

with a mildly abrasive cleaner.other material to enter

the gas orifice holder opening. Always keep the surface

burner cap and surface burner head in place whenever

a surface burner is in use.

Oven Cavity:

• Do not use oven cleaners, cleaning powders, steel

wool pads, synthetic fiber pads, or any other

materials that may damage the surface finishing.

• To clean the oven bottom, gently lift the bake

element. This will allow easier access to the oven bottom

for cleaning. Be careful not to raise the element more

than 4 or 5 inches from the resting position.

• Clean with warm soapy water; rinse and dry with a

clean soft cloth.

Lift-Off Oven Door:

• The oven door is removable for cleaning. To remove:

• Open the door to the fully opened position.

• Pull up the lock located on both hinge supports and

engage it in the hook of the hinge levers. You may

have to apply a little downward pressure on the door

to pull the lock fully over the hooks.

• Grasp the door by the sides; pull the bottom of the

door up and toward you to disengage the hinge

supports. Keep pulling the bottom of the door toward

you while rotating the top of the door toward the

range to completely disengage hinge levers.

To replace: reverse the process above.

Cleaning the Inner Door:

• Soap and water should suffice; Heavy spattering or

spillovers may require cleaning with a mildly

abrasive cleaner.

• Use a glass cleaner to clean the glass on the inside

of the door.

Cleaning the Outer Door:

• Use soap and water to thoroughly clean the top,

bottom, sides, and front of the oven door; rinse well.

• Do not let water drip into the vent openings.

• Use a glass cleaner to clean the glass on the outside

of the door.

CAUTION! Use caution when replacing the burner

cap so the electrode is not damaged. This may cause

a delayed ignition or prevent the burner from

igniting.

CAUTION! Any additions, changes or conversions

required in order for this appliance to satisfactorily

meet the application needs must be made by an

authorized distributor or qualified agency.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 34 35

Comments to this Manuals

No comments

Danby DR2099BLGLP User Manual Page 10

Comments to this Manuals

Related products and manuals for Radio Danby DR2099BLGLP