Danby Premiere DDR30A1GP Operations Instructions download pdf (Page 8)

,oocm

START

OPERATION

1)

Place

the

product

in an upright

position

on a flat,

stable,

ana

neat-

resistant surface. Make sure

there

is

nothin2 flammable

or

heat

sensitive

within (39 inches).Onerating

the

product

in any other

position coUld

cause

a

hazard

2)

Insert

the

plug into

a

suitable

wall

socket. The dehUmidifier

is

suitable

for

rating

on

an

electricity

supply

having

tlie

same voltage

as

tliat

showm

on its

rating

label.

3)

Make

sure

the water

tank

is correctly

located

.

After

switchinon the

machine

for the first

time

,

i

f

the

'Bucket

Full''

L

l]

:t'

t;rer

is

able

to

move

freely

,

then

return

the

water

tan

k

to the

correct

position

(Fig.

1).

WATER

FULL

INDICATOR

LIGHT (RED)

When

the

water

tank

is full

and/or incorrectly positioned inside

the

cabinet,

the water

full red

light

turns on and

remains

on

until such

time

that

the

tank

is

emptied

and/or

correctly

re-positioned

This

conditio

n

will

result

in

the

immediate

shut down of

the dehwnidifving system (both

com_pressor

and fan

motor

erations

are

terminated).This

is a

safety

feature

.

When

the

walerfarik

is

emptied andlor

correctly

re-positioned

,

the

dehumidifier

Will

resume operation

automatically.

NOTE:It

may

take

several minutes

before operating

conditions

resume.

BUCKET

FULL

LIGHT

•

When

the

water tank

is full the

machine will stop

and

the"Bucket

Full,light will

illuminate.

•

The water tan

k

should

be

carefully removed from

the

machine

by

slid4tg

it outward

from

the front

of the

unit, and

it

shOuld

be

emptied.

When

the

eJ!!P.1y

tank:

is replaced

properly

in

the

machine,

the

unit will

start up and run

normally

(¥ig. 2).

NOTE:Please

use both hands to carefully empty the water

tank.

DEFA

F

U

A

L

C

T

T

S

O

E

R

T

Y

TING

Each

time

the unit

is

disconnected/re-connected

and/or

in

the event

of a

power

failure,

the electronic

circuitboard

automatically defaults

to

1he

following

factorY

setting:

Humidity Setting:

60%

Fan

Speed:

Low

NOTE:

In

te

event of a

power failure

,

the unit will

default

to the last

program setting

that was used

when

power ts restored.

WATER

TANK

ProJJC!:

installation

of the

water

tank

is

crucial

in

maintaining reliable

dehumidifier

OPERATION

on.

The water

tan

k

holds accumulated condensed water anc;

!>Y

means

of a safety

switch

,

controls

both the

water level

and

operation

of

the dehumidification

process.

When the

water

tank.

is

full and/or accidentally displaced inside

the

cabinet,

the

float

switch actuator

(inside

the tank)

breaks contact with the

safety

switcli.This condition results

in the

immediate shut

down of the

compressor

and

fa

n

motor system, preventing moisture

from

being

condensed.

NOTE:Never

tamper with

or

attempt

to defeat

the

water level

(safety)

float

switch

system.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 17 18

Comments to this Manuals

No comments