Danby DPAC8399 User Manual Page 20

  • Download
  • Add to my manuals
  • Print
  • Page
    / 36
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 19
Remote Control Features
The hand held remote unit allows you to control all
operational aspects (excluding Auto-Timed
Programs) of your Portable 4 Season Home Comfort
Appliance from the convenience of your favorite
armchair. Here are some things you should know
about operating the unit with the hand held remote.
Upper Control Buttons
I/O: Power switch (On/Off).
Mode: Selects the operating mode
(Auto–Cool–Dry/Dehumidifier–Heat–Fan).
The "auto" mode is a built in feature activated from
the hand held remote unit only. Under "auto" mode,
your unit will automatically select the required
operating mode based on temperature selection.
Dehumidifying mode is not operational under the
“auto” mode function.The main unit will respond
automatically, switching appropriately between
modes "cool-heat-fan" to maintain the selected
temperature.
Fan:
Selects fan speed settings (Auto–LOW-MED-HIGH).
NOTE: The “Auto” fan speed setting is
equivalent to “Medium” fan speed.
Used to adjust (increase) both time of day
clock settings and temperature settings.
(1 min. increments) for time of day clock settings.
(1° increments) on the Celsius scale.
(2° increments) on the Fahrenheit scale.
Used to adjust (decrease) both time of day
clock settings and temperature settings.
(1 min. increments) for time of day clock settings.
(1° increments) on the Celsius scale.
(2° increments) on the Farenheight scale.
Lower Control Buttons
(Under Lower Sliding Cover)
Swing: Used to activate automatic air swing
(oscillating) feature (70° swing).
Set: Used to lock/register time of day setting.
Clock: Used to initiate time of day clock setting.
L: (Lock) Used to lock a selected program mode
(Against accidental program change).
R: (Re-set) Used to cancel/reset locked programs.
(Clock setting will also be erased)
˚C/˚F: Used to select temperature settings in either
“Celsius” or “Farenheight”.
To operate the remote, you will require two “AAA”
Alkaline batteries (included).
Batteries should be replaced when:
a) No signal (beep) is heard while attempting to
program the main unit.
b) No symbol “ ” appears in the remote LCD
window when a command is initiated.
Battery replacement:
1. Slide the lower control cover on the remote down
until it stops. Continue pulling (gently) until the
lower section separates completely from the unit.
2. Insert batteries (AAA) as depicted inside the
battery chamber.(+/-)
3. Re-install lower cover.
4. If the remote control is not being used for
extended periods of time (vacations etc.),
batteries should be removed.
The remote operates within a range of 7 meters
(23 ft.) from the receiver located inside the main unit.
Any obstruction between the receiver and remote
may cause signal interference, limiting the ability to
program the main unit.
NOTE: The illuminated control panel feature on
the main unit is not operational when setting
functions using the remote control unit. (this is
normal)
TEMP/TIMER
El tanque de agua externo
Esta unidad viene equipada con un "tanque de agua externo"
secundario (el tanque con el conector rápido tiene que estar instalado
por el consumidor). El conector rápido está instalado por la factoría y
viene con la unidad principal. Se encuentra por la parte trasera de la
unidad. Cuando el tanque de agua externo está conectado a la
unidad principal se aumentará el tiempo de funcionamiento de la
unidad (modo de aire acondicionamiento y deshumidificación
solamente) hasta 12 horas, incluso los dos tanques (según las
condiciones de humedad). Es posible operar esta unidad usando el
tanque de agua interno (principal) solamente. Sin embargo, el tiempo
de funcionamiento se disminuirá. Si el tanque de agua externo no
está conectado a la unidad el flujo de agua está desviado
automáticamente por dentro del tanque de agua interno.
Durante los modos de aire acondicionamiento y deshumidificación
agua condensada se acumula en una bandeja pre-enfría localizada
por debajo de las bobinas de evaporación (bobinas de refrigeración).
Cuando el nivel de agua por dentro del tanque llega a un nivel
predeterminado el flujo de agua está desviado primordialmente al
tanque de agua secundario. Cuando el nivel de agua dentro del
tanque de agua secundario llega a un nivel predeterminado el flujo
de agua invertirá (hacia atrás) y estará desviado por dentro del
tanque de agua interno principal. Cuando el nivel de agua dentro del
tanque de agua principal llega a un nivel predeterminado el
mecanismo del conmutador flotando se active automáticamente, lo
que causa la unidad de apagar automáticamente (aire
acondicionamiento y deshumidificación). El motor del ventilador
continuará operando (esto es normal).
NOTA: El mecanismo del conmutador flotando se activa según el
nivel de agua dentro del tanque interno (tanque principal
solamente).
Nota: Los accesorios del conector rápido que están suministado con
la unidad principal y el tanque de agua externo están coneciones
auto-cerrandos.
Es decir que tan pronto como desconecta las coneciones el flujo de
agua deja inmediatamente entre la unidad principal y el tanque de
agua externo.
Instrucciones para la instalación del tanque de agua
externo:
1. Usando 2 tornillos suministrados asegure la reborde apoyante para
el tanque de agua externo (con las ruedecillas instaladas a la
factoría) al soporte (consulte la figura 35).
Nota importante: Es posible que usted pierda los tornillos
originales que están suministrados. Para evitar daños a la
sistema cerrada nunca usar tornillos de reemplazo más larga
de 16mm (5/8 pulgadas).
2. Saque el conector rápido del tanque de agua (macho) que se
encuentra por dentro del tanque de agua y asegurelo al conector
hembra que se encuentra sobre el tanque de agua externo, apreta
moderadamente (consulte la figura 36).
Fig.35
Fig.36
Page view 19
1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 35 36

Comments to this Manuals

No comments