Danby DPAC8399 User Manual Page 19

  • Download
  • Add to my manuals
  • Print
  • Page
    / 36
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 18
Setting the AUTO-ON & AUTO-OFF TIMER
Before setting the AUTO-ON & AUTO-OFF Timer,
the time of day clock must be set/operational. You
must also select the appropriate operating MODE.
After the appropriate settings have been made, turn
off the unit.
1) Press the TIMER-ON key pad to initiate the
AUTO-ON time sequence. (Fig. 32). The display
window will indicate TIMER-ON and the word ON
will flash for 5 seconds. Press the
or key pad to select the desired AUTO-ON
start time. (Fig. 32a).
key pad will decrease the AUTO-TIMED
setting in 10 minute increments.
keypad will increase the AUTO-TIMED
setting in 10 minute increments.
When the desired time is established, (the time
will flash in the display window) press the
CLOCK key pad to register the AUTO TIMER-
ON program. The word ON will stop flashing and
remain “on” (TIMER ON) indicating the program
is set. The time of day clock setting will
immediately revert back in the display window.
The unit must remain “OFF” while programming
the AUTO-OFF program.
2) Press the AUTO-OFF key pad to initiate the
AUTO-OFF time sequence. (Fig. 33). The
display window will indicate TIMER-OFF and the
word OFF will flash for 5 seconds. Press the
or key pad to select the desired AUTO-
OFF time. (Fig. 32a).
key pad will decrease the AUTO-TIMED
setting in 10 minute increments.
keypad will increase the AUTO-TIMED
setting in 10 minute increments.
When the desired time is established, (the time
will flash in the display window) press the
CLOCK key pad to register the AUTO TIMER-
OFF program. The word OFF will stop flashing
and remain “on” (TIMER OFF) indicating the
program is set. The time of day clock setting will
immediately revert back in the display window.
When the AUTO-ON & AUTO-OFF times are set,
within the same program sequence, the display
window shows TIMER ON OFF identifying that both
ON and OFF times are now programmed
(Repeatable daily until until such time the program is
canceled and/or changed).
IMPORTANT: The desired AUTO-ON & AUTO-
OFF time must be registered within a 5 second
period (after pressing the TIMER-ON/OFF key
pads) otherwise the selected time will not
register and the system will automatically revert
back to the regular “time of day” clock setting
The unit will start automatically when the specified
AUTO-ON time is achieved on the time of day clock
and will stop automatically when the specified
AUTO-OFF time is achieved on the time of day
clock. To cancel or override the AUTO-TIMED
program, simply turn the unit on or off prior to the
scheduled AUTO-ON/OFF time. You can verify the
AUTO-ON/OFF time selection anytime by pressing
each respective TIMER-ON/TIMER-OFF key pad
and the selected time will temporarily appear
replacing the time of day clock for approximately
5 seconds.
Instrucciones para la instalación
del tanque de agua (continúa)
3. Ponga el tanque de agua a la posición correcta sobre la reborde
apoyante. Asegúrese de que el conector rápido sobre el tanque de
agua está alineado con el conector rápido, instalado a la factoría,
localizado al posterior del armario. (véase la figura 37)
4. Para hacer la coneción, empuje el conector del tanque de agua en
el conector del armario. Ud. va a oír un chasquido positivo cuando
hace la coneción
5. Instale la tapa sobre el tanque de agua.
6. Para desenganchar (desconectar) el tanque de agua externo,
apreta el botón de desenganchar que está en la parte superior del
conector rápido del armario, pues sujete los mangos de
desenganchar localizado por ambos lados del tanque,
levante y tire hacia adelante. (véase la figura 38, 39)
Fig.38
Fig.37
Fig.39
PRECAUCIÓN
Es necesario vaciar el agua acumulada en ambos tanques
antes de mover la unidad.
Page view 18
1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 35 36

Comments to this Manuals

No comments