Danby ADR3006 User Manual download pdf (Page 10)

Choix de l’emplacement :

Choisir un emplacement approprié, avec accès facile à

une prise de courant (éviter l’emploi d’une rallonge). S’il

est absolument nécessaire d’utiliser une rallonge pour

l’alimentation de l’appareil, utiliser uniquement une

rallonge agréée pour climatiseur (disponible dans la

plupart des magasins de quincaillerie)

Choisir un emplacement où rien n’entravera la

circulation de l’air à travers la grille d’admission avant.

Maintenir une distance de séparation d’au moins 20 cm

entre les murs adjacents et l’arrière de l’appareil, pour

optimiser l’efficacité et la circulation de l’air.

L’appareil fonctionne au niveau d’efficacité maximum

lorsque la température ambiante de la pièce est située

entre 6ºC et 35ºC.

Il est important de noter que l’efficacité d’un

déshumidificateur sera influencée par la taux de

réintroduction d’air humide dans la pièce. Pour obtenir

la meilleure efficacité, il convient de faire fonctionner le

déshumidificateur dans un espace ferme. Fermer

toutes les portes et fenêtres.

INSTALLATION

Indicator Light Function:

Power Light (Green):

When the unit is first connected to an electrical outlet,

the (green) power light starts to flash and continues to

flash until the “on/off” button is pressed. When the “on/off”

button is activated, the flashing (power) light turns to a

steady state “on” condition. The dehumidifier will

automatically default to the factory default setting. (See

Factory Default Setting for details)

IMPORTANT NOTE: Depending on the humidity

conditions of the surrounding environment, the

dehumidifier may not start automatically when the “on/off”

button is pressed.(see dehumidifier operating instructions

for details)

In the event of a power failure, the unit will not re-start

automatically when power is restored. To re-start the unit

you must press the "on/off" keypad again.

Water Full Indicator Light (Red):

When the water tank is full and /or incorrectly positioned

inside the cabinet, the (water full) red light turns on and

remains on until such time the tank is emptied and/or

correctly re-positioned. This condition will result in the

immediate shut down of the dehumidifying system. (both

compressor and fan motor operation are terminated) This

is a safety feature. When the water tank is emptied and/or

correctly re-positioned, the dehumidifier will resume

operation automatically. NOTE: It may take several

minutes before operating conditions resume.

Factory Default Setting:

Each time the unit is disconnected/re-connected and/or in

the event of a power failure, the electronic circuit board

automatically defaults to the following factory setting.

Humidity Setting: 60%

Fan Speed: Low

NOTE:

In the event of a power failure, all previous settings

are automatically erased/cancelled. If your program

setting was different than the above (default setting) it will

be necessary to re-program your settings. When the unit

is switched "Off” manually (using the on/off keypad) the

unit will always default to the last program setting that

was used.

Water Tank Operation:

Proper installation of the water tank is crucial in

maintaining reliable dehumidifier operation.

The water tank holds accumulated condensed water and

by means of a safety switch controls both the water level

and operation of the dehumidification process.

i.e. When the water tank is full and/or accidentally

displaced inside the cabinet, the float switch actuator

(inside the tank) breaks contact with the safety switch.

This condition results in the immediate shut down of the

compressor and fan motor system, preventing moisture

from being condensed.

IMPORTANT: Never tamper with or attempt to defeat the

water level (safety) float switch system.

Operating Instructions

1 2 ... 5 6 7 8 9 10 11 12 13 14

Comments to this Manuals

No comments

Danby ADR3006 User Manual Page 10

Comments to this Manuals

Related products and manuals for Air equipment Danby ADR3006